52梯控论坛

标题: 求教，怎么改通楼，目前是到7楼，东芝的系统 [打印本页]
作者: ijieshi    时间: 2020-1-6 23:43
标题: 求教，怎么改通楼，目前是到7楼，东芝的系统
本帖最后由 ijieshi 于 2020-1-7 17:11 编辑

楼层是 负一 负二 1到15楼  备注：负一 负二 1层 不用刷卡的 ，直接按电梯按钮就可以
0 扇区
0 区块: E6 E8 E2 12 FE 08 04 00 62 63 64 65 66 67 68 69
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

1 扇区
0 区块: 54 4F 53 48 49 00 44 5A 00 02 00 00 07 3D 00 04
1 区块: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: A7 54 DE 67 A1 03 FF 07 80 FF A0 A1 A2 A3 A4 A5

作者: jatpl2007    时间: 2020-1-7 00:33
1扇区0区块最后一个字节改成05，1区块全00
作者: 世纪龙庭    时间: 2020-1-7 00:40
jatpl2007 发表于 2020-1-7 00:33
1扇区0区块最后一个字节改成05，1区块全00

为何要改成05啊？
作者: 世纪龙庭    时间: 2020-1-7 00:40
jatpl2007 发表于 2020-1-7 00:33
1扇区0区块最后一个字节改成05，1区块全00

为何要改成05啊？
作者: jatpl2007    时间: 2020-1-7 00:52
世纪龙庭 发表于 2020-1-7 00:40
为何要改成05啊？

东芝通楼是固定的，必须是05，楼层信息全00
作者: xulan8314    时间: 2020-1-7 03:35
怎么没看到时间呢，无限制？
作者: hjchzld    时间: 2020-1-7 04:55
作者: jjh826078240    时间: 2020-1-7 09:52
不懂，也是看看支持一下
作者: ijieshi    时间: 2020-1-7 10:57
jatpl2007 发表于 2020-1-7 00:33
1扇区0区块最后一个字节改成05，1区块全00

1扇区
0块    544F53484900445A000200000C9B0004
1块    00881500000000000000000000000000

上面是到12楼的，按照你说的改动后刷电梯卡无反应
作者: ijieshi    时间: 2020-1-7 10:58
xulan8314 发表于 2020-1-7 03:35
怎么没看到时间呢，无限制？

貌似这个电梯卡物业没设时间
作者: qqqzxc    时间: 2020-1-7 11:09
0 扇区
E6 E8 E2 12 FE 08 04 00 62 63 64 65 66 67 68 69
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

1 扇区
54 4F 53 48 49 00 44 5A 00 00 00 00 07 3D 00 04
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
A7 54 DE 67 A1 03 FF 07 80 FF A0 A1 A2 A3 A4 A5
替换原数据
作者: ijieshi    时间: 2020-1-7 13:10
1扇区
0块    544F53484900445A000200000C9B0004
1块    00881500000000000000000000000000

试了下几个同事的卡，他们的1块都是8815，为什么就我的是8000,大家都是0块标红的不一样，其他都一样
作者: ijieshi    时间: 2020-1-7 13:13
qqqzxc 发表于 2020-1-7 11:09
0 扇区
E6 E8 E2 12 FE 08 04 00 62 63 64 65 66 67 68 69
00 00 00 00 00 00 00 00 00 00 00 00 00 00 0 ...

感谢！晚上按你这个改掉，明天试刷下，还有请问：

1扇区
0块    544F53484900445A000200000C9B0004
1块    00881500000000000000000000000000

试了下几个同事的卡，他们的1块都是8815，为什么就我的是8000,大家都是0块标红的不一样，其他都一样
作者: xulan8314    时间: 2020-1-7 16:38
0块红字是编码，就是都不一的。1块红字是楼层信息
作者: xulan8314    时间: 2020-1-7 16:51
你的原卡可以到-1和—2吗，我怎么查出来80是6楼呢
作者: ijieshi    时间: 2020-1-7 16:52
xulan8314 发表于 2020-1-7 16:38
0块红字是编码，就是都不一的。1块红字是楼层信息

那如果8815是楼层信息，为什么能刷到的楼层不一样，有个同事和我一样懒得去物业改，也是刷不到12F，如果只改到能刷12F，怎么改呢
作者: ijieshi    时间: 2020-1-7 16:55
xulan8314 发表于 2020-1-7 16:51
你的原卡可以到-1和—2吗，我怎么查出来80是6楼呢

去 负一 负二 1层 不用刷卡的 ，直接按电梯按钮就可以
作者: xulan8314    时间: 2020-1-7 19:00
本帖最后由 xulan8314 于 2020-1-7 19:30 编辑
ijieshi 发表于 2020-1-7 16:52
那如果8815是楼层信息，为什么能刷到的楼层不一样，有个同事和我一样懒得去物业改，也是刷不到12F，如果 ...

试试8010看看，改成8010是你现在的7楼和12楼，单12楼就8010改成0010,。
我最奇怪的事1区0块，你的最后两位是04，正常东芝的都是0A或是05
作者: xulan8314    时间: 2020-1-7 19:04
本帖最后由 xulan8314 于 2020-1-7 19:05 编辑

8815看看是不是可以按到多层去啊？3层 7层8层12层可用啊？完整数据发出来
作者: ijieshi    时间: 2020-1-7 19:32
xulan8314 发表于 2020-1-7 19:04
8815看看是不是可以按到多层去啊？3层 7层8层12层可用啊？完整数据发出来

0 扇区
0 区块: E6 E8 E2 12 FE 08 04 00 62 63 64 65 66 67 68 69
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

1 扇区
0 区块: 54 4F 53 48 49 00 44 5A 00 02 00 00 07 3D 00 04
1 区块: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: A7 54 DE 67 A1 03 FF 07 80 FF A0 A1 A2 A3 A4 A5

2 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

3 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

4 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

5 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

6 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

7 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

8 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

9 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

10 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

11 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

12 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

13 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

14 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

15 扇区
0 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: FF FF FF FF FF FF FF 07 80 69 FF FF FF FF FF FF

作者: xulan8314    时间: 2020-1-7 19:43
1 扇区
0 区块: 54 4F 53 48 49 00 44 5A 00 02 00 00 07 3D 00 05
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: A7 54 DE 67 A1 03 FF 07 80 FF A0 A1 A2 A3 A4 A5

1区改成这样先试试看，通层的，自己刷完卡，按楼层按钮试试吧
作者: ijieshi    时间: 2020-1-7 19:59
xulan8314 发表于 2020-1-7 19:43
1 扇区
0 区块: 54 4F 53 48 49 00 44 5A 00 02 00 00 07 3D 00 05
1 区块: 00 00 00 00 00 00 00 00 00  ...

已经这样改过，早晨刷电梯没反应
作者: ijieshi    时间: 2020-1-7 20:01
ijieshi 发表于 2020-1-7 19:59
已经这样改过，早晨刷电梯没反应

准备按上面仁兄的试下通层
1 扇区
54 4F 53 48 49 00 44 5A 00 00 00 00 07 3D 00 04
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
A7 54 DE 67 A1 03 FF 07 80 FF A0 A1 A2 A3 A4 A5
替换原数据
作者: xulan8314    时间: 2020-1-8 20:19
今天试了没，想了解结果
作者: ijieshi    时间: 2020-1-9 13:00
xulan8314 发表于 2020-1-8 20:19
今天试了没，想了解结果

通楼2种方案刷电梯没反应呀，目前在用8815，是到3F 7F 8F 10F 12F
作者: ijieshi    时间: 2020-1-9 13:02
ijieshi 发表于 2020-1-9 13:00
通楼2种方案刷电梯没反应呀，目前在用8815，是到3F 7F 8F 10F 12F

可以直接修改8815所在字节实现通楼不？
作者: xulan8314    时间: 2020-1-9 15:11
ijieshi 发表于 2020-1-9 13:02
可以直接修改8815所在字节实现通楼不？

改成FFFF，楼层高，多添加几个FF，慢慢试
作者: www9241307    时间: 2020-1-24 13:23
ijieshi 发表于 2020-1-7 19:32
0 扇区
0 区块: E6 E8 E2 12 FE 08 04 00 62 63 64 65 66 67 68 69
1 区块: 00 00 00 00 00 00 00 00 0 ...

1区2块13－16是日期
1区1 块2－8是楼层
作者: www9241307    时间: 2020-1-24 13:48
本帖最后由 www9241307 于 2020-1-24 13:50 编辑


1 扇区
0 区块: 54 4F 53 48 49 00 44 5A 00 02 00 00 07 3D 00 0A
1 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 区块: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 区块: A7 54 DE 67 A1 03 FF 07 80 FF A0 A1 A2 A3 A4 A5
作者: saldzs    时间: 2021-6-25 17:56
作者: jk8max    时间: 2021-11-30 10:57
不懂，也是看看支持一下



欢迎光临 52梯控论坛 (https://52tikong.com/) Powered by Discuz! X3.4